Step 1: Prepare the area and take measurements.
First, clean the door and the jamb, removing as much dirt and debris as possible. If any grime remains after scrubbing with soapy water, consider using fine-grit sandpaper to eliminate residual buildup.
Once you’ve got the doorway cleaned, proceed to do some measuring. Because you’ll want door seal strips along both sides of the door, as well as across the top and bottom, be sure to carefully measure all those areas.
Step 2: Tighten the door’s hinges.
Before you start cutting the weatherstripping, make sure the door hinges are tight. Using the doorknob, lift the door upward. If there’s some play, and the door moves upward, tighten the screws on the top hinge. And then make sure the screws in the bottom hinge are secure, as well. This ensures the door is tightly fitted and squarely hung, which will allow the newly installed weatherstripping to fit the gaps evenly and do its job properly.
Step 3: Measure the jamb.
You need to answer two questions. First, how wide is the gap between the door and jamb? (Be sure to measure twice, once along the side, and again along the top. These measurements might differ.) Second, how wide is the jamb? While the answer to the first question tells you how thick the weatherstripping you purchase can be, the second answer reveals how wide. Plan to buy enough weatherstripping to run across the width and height of the door, plus about 10 percent extra.
Step 4: Choose the correct weatherstripping.
Weatherstripping comes in a variety of materials. Each has pros and cons. Felt weatherstripping offers the benefits of being cheap and very easy to cut and install, but because it’s not very durable, it’s rarely used on doors.
Marginally more expensive is easy-install foam weatherstripping. Though foam wears better than felt, neither boasts the durability of rubber weatherstripping, the most expensive option. Rubber insulates well, but it can be somewhat challenging to install. Unlike the other options, it often must be nailed into place.
Step 5: Cut the weatherstripping into segments, and check the cuts.
With your chosen weatherstripping at the ready, proceed to cut three pieces: One piece for the top of the door, and two for the sides.
Step 6: If required, adjust the cut.
Before you begin to permanently apply the new weatherstripping, hold each of your pieces up to the doorframe to confirm you’ve cut the lengths properly. If they’re a bit too long, that’s ok; you can trim the excess after the stripping is in place.
If any of your strips are too short, however, you’ll want to check your measurements and cut a new piece.
Step 7: Tack, snap, or adhere the weatherstripping to the door.
If the product features an adhesive back, peel it away and press it into place around the perimeter of the door jamb, not the door itself. Even if your weatherstripping has adhesive, you may wish to reinforce the installation with heavy-duty staples or small tacking nails. Either will help keep the weatherstripping in place over time.
Step 8: Install a door sweep.
To complete the job, install a sweep along the bottom of the door. The most common type of door sweep consists of a metal band from which a strip of rubber juts down (view example on Amazon). When the door opens, the rubber flexes so as not to be an impediment, and when the door closes, the rubber provides a strong air seal.
Door sweeps come in standard sizes, but if you cannot find one whose width matches that of your door, you can use a hacksaw to cut the sweep down to size. Attach the right-size sweep to the door using the screws provided. Because these screws tend to be small and not self-tapping, it’s best to predrill holes for them by means of an electric drill/driver. Position the sweep so that it seals tightly against the threshold.
From start to finish, the door weatherstripping process should take no longer than an hour. That’s a small time commitment to ensure that you remain comfortable through the winter, without spending a fortune on to keep the house warm. Though it’s a simple project, weatherstripping really is one of the most effective ways to stop drafts and the discomfort they cause.
The Benefits of Door Weatherstripping
- Weatherstripping a door helps prevent hot and cold air from escaping or coming in your house, offering considerable savings on energy bills—as much as 20 percent
- Weatherstripping can help prevent rain from being driven under your door and into your home
- Weatherstripping can also be a barrier to bugs
Final Thoughts
Weatherstripping is among those joyful home improvement “fixes” that often offer significant benefits at a fairly low cost and without too much work. Properly installed, weatherstripping can help reduce heating and cooling costs by 20 percent. Weatherstripping can also keep insects and rain out of your home. And guess what? Weatherstripping is fairly easy to install and can be done in less than an hour.
FAQs
Q. What is the best weatherstripping for doors?
At any home improvement center, you’ll find a number of types of weatherstripping, including tapes, v-strips or v-seals, gaskets, and sweeps. For doors, most pros and DIYers find that gaskets and sweeps work best.
Q. How do I stop rain from coming under my door?
Properly applied weatherstripping can help prevent rain from coming under your door. Incidentally, weatherstripping is also used on interior doors as soundproofing.
